Вход в биллинг - Billing entrance - www.CardsharingServer.com

English forum section

Автор Тема: MGcamd Configuration to load SoftCam.Key  (Прочитано 10788 раз)

LightMoon

  • Новичок
  • *
  • Сообщений: 2
MGcamd Configuration to load SoftCam.Key
« : 01 Августа 2014, 10:36:37 »
Hi,

As far as I am concern, Mgcamd 1.35 should load SoftCam.Key by default but this is not happening for me, it good to mention that my Receiver ( IPBox 01 HD with latest Sifteam Firmware based on DGS ) which does not have access to Internet so the only choise that I have is using SoftCam.Key

This the procedure that I went through.
First of all installed MgCamd 1.35 and then downloaded the latest SoftCam.Key from this topic and put here ( /var/keys ) and changed the whole files' permission in that directory to 755.

Unfortunately after all these effort nothing come out of it :(

This is my mg_cfg configuration ( apart from mg_cfg every other file copied without any changes ) and this this is my log file.

# EMM messages
#    00 don't show any EMMs (default)
#    01 show only valid EMMs
#    02 show valid and bad EMMs with complete data display
M: { 01 }

# ECM messages
#    00 don't show anything about ecm
#    01 normal mode, show pids processed, decoded ecm and cw
#    02 verbose mode, show valid and bad ECMs with data
C: { 01 }

# AU
#    00 disable, no emm pids processed
#    01 enable, emm pids always processed for soft-au and shared cards
#    02 auto, emm started only if channel cant be decoded
#    03 process emm pids for network cards update only
A: { 02 }

# key update (sum 01 or 02 with 04)
#    01 update only new keys, default setting
#    02 update all keys (used for valid PMK checking)
#    04 enable TPS au
#    + tps SID, which pmt pid contains au pid
U: { 01 } 0x12c0

# config files folder (softcam, autoroll, ignore/priority)
#    00 files in /var/keys
#    01 files in /tmp
T: { 00 }

# network mode, use summ for several clients
#    00 no network (default)
#    01 newcamd netclient
#    02 radegast netclient
#    04 camd3 netclient
#    08 gbox netclient
#    32 cccamd netclient, card list saved as /tmp/cccamd.info
#    (ECM only, supported server version up to 2.1.1, later not work)
G: { 33 }

# network retry, use summ for several options
#    00 disable
#    01 retry every new ecm
#    02 try to connect to offline shares every Q: seconds
#    04 try to detect and fast reconnect to lost (and not used atm) server
#    + XX messages number and YY seconds to reconnect
#    mg will reconnect to server, if no answer to last XX ecm/keepalive or
#    if no answer for last ecm or keepalive sent for YY seconds
#    set to 0 to disable
N: { 01 } 5 30

# network ecm timeout in seconds
K: { 01 }

# newcamd dead routes connect retry, sec
Q: { 60 }

# network shares priority
# 00 gbox, newcamd, cccamd, radegast, camd3 (default)
# 01 camd3, radegast, cccamd, gbox, newcamd
# 02 cccamd, newcamd, camd3, gbox, radegast
P: { 00 }

# on screen display type
#    00 No OSD (default)
#    01 neutrino
#    02 enigma
#    03 relook
#    + user password for http auth
O: { 00 } username password

# on screen display Options, summ of:
#    01 show emu ecm
#    02 show network shares messages
#    04 show decoding failed / fta
#    08 show emm keys update
#    + web port to use for osd
S: { 03 } 80

# Log option, summ of:
#    00 off
#    01 network udp log
#    02 log to console
#    04 file, appended ! delete it by yourself, before it eat all your hdd
#    + IP udp-port log-file-name
L: { 01 } 192.168.10.200 514

# keep ecm cache, seconds
# every cache entry takes 28 bytes, so 24h cache will take *only* 240-400kb of memory,
# for openbox/elanvision users with remote shares make sense to set it higher than default value,
# to not hammer cards while timeshifting or playing crypted recordings.
E: { 15 }

# cache option, summ of:
#    00 Off (default)
#    01 Ecm pids cache, store pids used to decode in /tmp/ca_cache.list at exit, load at startup, same syntax as restore.list
#    02 Ecm data cache, remember CW for (E:) time
#    04 Emm cache for network cards, do not resend the same emm twice, cache not cleared until restart
H: { 07 }

# reread files, summ of:
#    00 No (default)
#    01 reread config file on channel change (including priority and ignore, but not replace/cache)
#    02 reread SoftCam.Key on channel change
#    04 reread SoftCam.Key if file changed
R: { 00 }

# debug, summ of
# 00 off (default)
# 01 debug ecm
# 02 debug emm
# 04 debug network ecm
# 08 debug network emm
# 16 debug network login
# 32 show mem/cpu stats every 1 min
# 64 add timestamp to log messages
D: { 00 }

# box type
# 00 autodetect, change only if you think wrong type detected.
# 01 dbox2
# 02 dreambox
# 03 triple-dragon
# 04 relook
# 05 openbox
# 06 dreambox/mips
# 08 stapi/kathrein
# 09 stapi/ipbox
# 11 stapi/openbox
B: { 12 }

# map all 180x nagra caids to 1801
# default is 01
F: { 01 }

Aug 01 10:57:55 192.168.10.30 tuxbox mgcamd v1.35 by mixvt (compiled Jan 20 2010 22:15:45)
Aug 01 10:57:55 192.168.10.30 [mg] Net:33:1:0:1s Show ecm:1, emm:1 Up:1 Au:2 Dir:0 Osd:no:80:0 Cache:7 Log:1:192.168.10.200:514 Reread:0
Aug 01 10:57:55 192.168.10.30 [mg] Ecm cache time: 15
Aug 01 10:57:55 192.168.10.30 Box type: openbox/stapi
Aug 01 10:57:55 192.168.10.30 Conax.Key error 2: No such file or directory
Aug 01 10:57:56 192.168.10.30 Keys readed
Aug 01 10:57:56 192.168.10.30 Conax.Key error 2: No such file or directory
Aug 01 10:57:56 192.168.10.30 [config] newcamd route = ipbox:127.0.0.1:10110 server cardserver
Aug 01 10:57:56 192.168.10.30 [config] newcamd route = ipbox:127.0.0.1:10010 server cardserver
Aug 01 10:57:56 192.168.10.30 newcamd keep alive: 300, incoming port: 0
Aug 01 10:57:56 192.168.10.30 [mgcam] emm thread started
Aug 01 10:57:56 192.168.10.30 [newcamd] Connecting to 127.0.0.1:10110...
Aug 01 10:57:56 192.168.10.30 [newcamd] Connecting to 127.0.0.1:10010...
Aug 01 10:57:56 192.168.10.30 [cccamd] My nodeID 50fe5c0b885f8910
Aug 01 10:57:56 192.168.10.30 [newcamd] Connection to 127.0.0.1:10110 failed (3ms)
Aug 01 10:57:56 192.168.10.30 [newcamd] Connection to 127.0.0.1:10010 failed (4ms)
Aug 01 10:57:56 192.168.10.30 [mg0] service 14C2 index 0 pmt pid 0 (1)
Aug 01 10:57:56 192.168.10.30  CaPID: 0x18CB ProvID: 000000
Aug 01 10:57:56 192.168.10.30  CaPID: 0x1CB3 ProvID: 000000
Aug 01 10:57:56 192.168.10.30 [mg0] network can't decode
Aug 01 10:57:56 192.168.10.30 [mg0] pid 0x18CB failed to decode.
Aug 01 10:57:56 192.168.10.30 [mg0] No irdeto key(s) found for id 0 keynr 00
Aug 01 10:57:56 192.168.10.30 [mg0] network can't decode
Aug 01 10:57:56 192.168.10.30 [mg0] No irdeto key(s) found for id 80 keynr 00
Aug 01 10:57:56 192.168.10.30 [mg0] network can't decode
Aug 01 10:57:56 192.168.10.30 [mg0] pid 0x1CB3 failed to decode.
Aug 01 10:57:57 192.168.10.30 [mgcamd] emm started
Aug 01 10:57:57 192.168.10.30  CaPID: 0x0604 ProvID: 000000
Aug 01 10:57:57 192.168.10.30  CaPID: 0x0605 ProvID: 000000
Aug 01 10:57:57 192.168.10.30  CaPID: 0x0604 ProvID: 000000
Aug 01 10:57:57 192.168.10.30 [mgcamd] emm stopped

Since I am new to this concept I tried to put as much detail as I could to lessen the ambiguity of my case.
I really appreciate to tell me what should do now or what have I done wrong,

Thanks in Advance.

suma

  • Главный помощник Moderatora
  • Ветеран
  • ****
  • Сообщений: 9165
  • Keep trying!
Re: MGcamd Configuration to load SoftCam.Key
« Ответ #1 : 01 Августа 2014, 11:08:45 »
Hi,
it good to mention that my Receiver ( IPBox 01 HD with latest Sifteam Firmware based on DGS ) which does not have access to Internet

If your receiver has no internet connection, the only choice for you (if you want cardsharing) is MPCS software (to be installed on your PC).
Typically, we recommend all users to delete Softcam.key as it prevents receiver from sharing via internet.
You have to determine whether you use sharing OR you use softcam. Both options are not recommended (though, possible).
The settings that you get from the billing when taking a free test or making subscription, must be used in emulator built-in to your receiver. If you cannot physically set up emulator for sharing, you need to adjust it by enabling it for sharing. Be sure that your receiver can be adjusted for sharing by enabling EMU.
First, take a free test and try to adjust EMU (receiver) and MPCS (PC) communication.
You will find more information on MPCS here https://www.cardsharing.cc/index.php?topic=1362.0
Don't even try to use only softcam.key if you want sharing to work, we recommend to delete it at all. These are two things incompatible.

regards
VU+Zero. 13E, 82.5E, 56E, Vip All, OpenPLI 6.0 image, OSCam: 1.20-unstable_svn. ALL POSTS WITHOUT SIGNATURE AND LOG-FILE will be ignored and deleted!1.mg_cfg here http://www.cardsharing.cc/index.php?topic=23717.msg58140#msg58140
2. ignore-priority.lists here http://www.cardsharing.cc/index.php?topic

LightMoon

  • Новичок
  • *
  • Сообщений: 2
Re: MGcamd Configuration to load SoftCam.Key
« Ответ #2 : 01 Августа 2014, 13:22:50 »
Hi,

First of all, Thanks for such a quick reply.
The problem is there isn't any permanent link between my Laptop and the Receiver and I only use Ethernet Link to transfer files via FTP. So right now using the SoftCam option is available for me. Beside to tell you the truth, I'm not that much into TV and I just want to open some Digiturk channels on Eutelsat W3A (7.0°E) which I found the keys are available in SoftCam.Key and surprisingly works for folks. ( Anyways I attached the SoftCam.Key if you want to look at )

I want to ask you despite the routine help me to config my IPBox and Mgcamd to serve in this way.

Thanks In Advance

suma

  • Главный помощник Moderatora
  • Ветеран
  • ****
  • Сообщений: 9165
  • Keep trying!
Re: MGcamd Configuration to load SoftCam.Key
« Ответ #3 : 01 Августа 2014, 13:46:12 »
You found card-sharing server (we are exactly what you found).
We are dealing with card-sharing ONLY. Cardsharing supposes internet connection.
Unfortunately, we don't know how to use softcam with the model of your receiver, as it is beyond our competence.
You need to google and find out any support forums of your receiver. I believe, you will find all answers to your question.
Here, we consult our users how to set up their receivers properly in order to get the service they bought on our server.

regards
VU+Zero. 13E, 82.5E, 56E, Vip All, OpenPLI 6.0 image, OSCam: 1.20-unstable_svn. ALL POSTS WITHOUT SIGNATURE AND LOG-FILE will be ignored and deleted!1.mg_cfg here http://www.cardsharing.cc/index.php?topic=23717.msg58140#msg58140
2. ignore-priority.lists here http://www.cardsharing.cc/index.php?topic