Dreambox DM900 + OpenaTV 6.0 + OSCam + Hispasat CS (NOS)

[SerGeyyy]

I give you a link in German as exactly described how it goes with the setting of oscam on the firmware dreamelite 6.0

http://www.dreambox4k.com/tuto-installieren-sie-oscam-auf-dreamelite/

[farajpourm]

I did all the steps which you mentioned

[reader]
label       = "tvsharing"
protocol    = cccam
device      = server,port (here I put the IP address of card sharing
user        = xxx here I put the login number
password    = xxx here I put the password
group       = 1
cccversion = 2.3.0
audisabled  = 1
ccckeepalive = 1

[SerGeyyy]

[reader]
label       = "tvsharing"
protocol    = cccam
device      = server,port (here I put the IP address of card sharing,cccam port
user        = xxx here I put the login number
password    = xxx here I put the password
group       = 1
cccversion = 2.3.0
audisabled  = 1
ccckeepalive = 1

[farajpourm]

this is what I did of course without brackets:


[reader]
label       = "tvsharing"
protocol    = cccam
device      = (xx.xx.xx.xx),(40394)
user        = (9383561)
password    = (2335709)
group       = 1
cccversion = 2.3.0
audisabled  = 1
ccckeepalive = 1

[SerGeyyy]

that's right, Turn the receiver off for a short time and then turn it on again.Go to the encrypted sender and start oscam then it must work.If it does not work then you do something wrong. I use these settings and it goes 100% with all packete

[farajpourm]

SerGeyy thank you very much for your support. I appreciate that.
the problem was in my login number and password and port number. those numbers have been changed and I used the old details. I asked for new test parameters and now its working 
thank you once again.

[SerGeyyy]

No Problem farajpourm. If you still need help then please contact me I help you

[SerGeyyy]

 

[farajpourm]

Hi SerGeyyy,
I have new problem with DM900. its related to flashing a new image. I wanted to flash a new image but when I put the dm900 in rescue mode and I put the my dm900 IP in my pc browser it can not connect to Dreambox web site to browse and choose a new image. any idea where can be the problem?
thanks

[suma]

This is A,B,C of Dreamboxes (as well as any other linux based receivers).
You need to download dreamelite 6.0 firmware to your PC from internet. Google will help you.
Usually, firmware is packed to .zip or .rar archives. You need to unrar the archive on your PC.
Dreambox shall be connected to PC via router. If the test was working for you OK, it means that receiver can be controlled from PC.
I have no idea what is the procedure of manual installation of firmware on your DM900. Google this, too.

[farajpourm]

Hello Suma,
I did all of these things for more than 20 times within last one month. I have now the dreamelite 6.0 installed on my dm900. now I want to install a fresh image of dreamelite 6.0 on my DM900. when I put the DM900 in rescue mode and in my pc browser i write there my IP address I can not get the dreambox web site (that grey web site, see attached picture) to browse and insert the FW which I want to install. the connection is not possible. it seems that something blocking the box to contact. see attached file

[suma]

Did you check PC firewall?

[farajpourm]

I did not check it but I assume when I could flash other images before with no problems then the firewall should be ok .
it seems that the box not indeed goes in rescue mode. as I mentioned in my previous note that when I put the box in rescue mode and in my pc i put box IP address I should get that gray dreambox web site to flash new image. instead of that grey web site (dreambox web site) I get this picture in attached file with a red not in upper side center of the page that the session is not possible(something like that).
normally it should be in this way that when the DM900 is not in rescue mode(normal operation) and I put the box IP address in browser I get this page

[suma]

Which browser is used? I remember from my experience, it works only with IE. No other browsers supported this option.

[suma]

One more thing. When I long pressed the switch button on the front panel of my DM800, I saw internal IP address of the receiver. I don't know what is the procedure in your receiver. IP addresses should be the same on your receiver and the one you entered to the browser.

[farajpourm]

I don't know if its the same in DM900. later today I can try that. for rescue mode I switch on the box from back side then in less than one second I should put my finger on front led and then it will go to rescue mode. I get the IP address on DM 900 display and on the TV display. no issue with that

[suma]

Also try not to touch the switch from the back side. Try to unplug the box and plug it again simultaneously pressing front led.

[farajpourm]

I will try it today evening and will let you know if it work

[farajpourm]

Hi,
I solved the problem. I used another browser and it communicated without problem. before I used internet explorer and now I used Microsoft edge and flashed the image.

[Jogi]

unbelievable *g*
if I see your last post from 17th July: you want to use Oscam, right ? so why do you configure so much emulators ? have installed all of them ?? and you are really woundering ?
>>> I dont know what type of motor my car has, so I through in some sorts of petrol (leaded and unleaded), a portion of diesel, little bit LPG gas and a can of kerosin, all together with some alcohol - but its still not starting *headbanging*
Simply take a look at the logfile from your first post: your Oscam is trying to decode FFFE@FFFFFE... >> that does not looks right, I bed anything, that these are not the SRVID and the CAID of the channel you try to decode. Let say it with other words: this CS server has no package available to decode FFFE so the request will not be send to this server because it make no sense to send requests to wrong caids = cards. If your emulator on your box does not detect the service-id and caid correct it will never send it to the correct server. The server is fine, at the end of the log you reconnected from WebIF successful, but no requests to the server = disconnecting (optional Oscam settings I would not use)
My suggestion: remove all the garbage from your box, most likely best you can do is reinstall it completely and install ONE emulator you want to use and learn how to configure THIS ONE emulator
Oscam is not bad and for a start check out: http://www.streamboard.tv/wiki/OSCam