Вход в биллинг - Billing entrance - www.CardsharingServer.com

English forum section

Автор Тема: Scam 3.6 - ECM timing  (Прочитано 1974 раз)

Sebbo2111

  • Новичок
  • *
  • Сообщений: 3
Scam 3.6 - ECM timing
« : 10 Февраля 2015, 03:36:49 »
Hello,

i bought a linux based reciever Zgemma Star 2S. Only one tuner is in use. Secound planeed with new renewal.
I´ve tried to config mgcamd as suggested. Without seccess. So i tried Scam 3.6 - working fine - i checked connections history.
There are duplicated requests. I would like to set ECM timeout as suggested, but dont know how. Dr. Google didn`t help.
Do you kindly help me out.

2nd problem:
Various ECM requests simultaneously being sent to the main and reserve server.
Could there be a timeshifting problem? Using timeshifting not allowed?

3rd problem:
Requests for channel decoding above daily limit... Channels will be shifted with delay up to 10 seconds.

SO it`s forbidden to switch channel while recording one other... but possible by using dual login.

Thank you for support.
Whould like to avoid violating rules.

regards

Sebastian
 

suma

  • Модератор
  • Ветеран
  • *****
  • Сообщений: 9246
  • Keep trying!
Re: Scam 3.6 - ECM timing
« Ответ #1 : 10 Февраля 2015, 06:31:33 »
I´ve tried to config mgcamd as suggested. Without seccess. So i tried Scam 3.6 - working fine - i checked connections history.
There are duplicated requests. I would like to set ECM timeout as suggested, but dont know how. Dr. Google didn`t help.
Do you kindly help me out.

Hi,
Depends on the firmware. You must know which type of Enigma is used - E1 or E2. If E1 - mgcamd 1.31 is required, if E2 - mgcamd 1.35(a). Check and amend if necessary. To eliminate duplicated requests, delete backup server from your settings and restart emulator. Check connections history next day when statistics is zeroed.


2nd problem:
Various ECM requests simultaneously being sent to the main and reserve server.
Could there be a timeshifting problem? Using timeshifting not allowed?

Timeshift is allowed with dual-login. In your case - not allowed as it will be post-decoding (or delayed decoding).

3rd problem:
Requests for channel decoding above daily limit... Channels will be shifted with delay up to 10 seconds.

SO it`s forbidden to switch channel while recording one other... but possible by using dual login.


Right, if using dual-login, you will be able to watch one channel and record the other one. 10 seconds is a time to zap from one channel to the other. You cannot zap channels too fast as server will receive too much requests. Read the rules and try to zap channels not faster than every 10 seconds.
VU+Zero. 13E, 82.5E, 56E, Vip All, OpenPLI 6.0 image, OSCam: 1.20-unstable_svn. ALL POSTS WITHOUT SIGNATURE AND LOG-FILE will be ignored and deleted!1.mg_cfg here http://www.cardsharing.cc/index.php?topic=23717.msg58140#msg58140
2. ignore-priority.lists here http://www.cardsharing.cc/index.php?topic

Sebbo2111

  • Новичок
  • *
  • Сообщений: 3
Re: Scam 3.6 - ECM timing
« Ответ #2 : 11 Февраля 2015, 02:00:37 »
Hi,
Depends on the firmware. You must know which type of Enigma is used - E1 or E2. If E1 - mgcamd 1.31 is required, if E2 - mgcamd 1.35(a). Check and amend if necessary. To eliminate duplicated requests, delete backup server from your settings and restart emulator. Check connections history next day when statistics is zeroed.

-----

I´ve check Enigma version .... image is openATV 4.2 an Enigma2 image...


Sebbo2111

  • Новичок
  • *
  • Сообщений: 3
Re: Scam 3.6 - ECM timing
« Ответ #3 : 11 Февраля 2015, 02:04:45 »
Hello,

duplicated requests eliminated. Thanks a lot...

another problem shew up...

Number of requests for CAID/IDENT invalid for the port
IMPORTANT! Your receiver is sending requests to a port forcefully ignoring the filters installed at the server. Delete different filters and mappings affecting replacement of CAID or IDENT from your emulator settings (ex., delete replace.list file)

there is no such file

suma

  • Модератор
  • Ветеран
  • *****
  • Сообщений: 9246
  • Keep trying!
Re: Scam 3.6 - ECM timing
« Ответ #4 : 11 Февраля 2015, 06:05:43 »
Hello,
On the forum, we provide our users with recommended configs for MgCamd emulator https://www.cardsharing.cc/index.php?topic=28088.0
Unfortunately, we have no idea how to set up your Scam 3.6 as our server is mainly adjusted for MgCamd emulator (working with Newcamd protocol). Use Google to find out the way out.
VU+Zero. 13E, 82.5E, 56E, Vip All, OpenPLI 6.0 image, OSCam: 1.20-unstable_svn. ALL POSTS WITHOUT SIGNATURE AND LOG-FILE will be ignored and deleted!1.mg_cfg here http://www.cardsharing.cc/index.php?topic=23717.msg58140#msg58140
2. ignore-priority.lists here http://www.cardsharing.cc/index.php?topic