golden media 9060

[cardsheranski]

Hi,

I'm experiencing problems with some channels of cyfra+ included in vipholland package.

The channels are canal+ film, hbo and hbo . When I watch those channels I constantly get glitches every 10-15 seconds en eventually I get banned from the server for 10 minutes. All other channels of canal digital (rtl 4 ,rtl 5, mtv's, film1 action, sport1 tennis), polsat cyfrowy and also cyfra + channels such as canal+ sport are working without glitches and any problems.

I have a golden media 9060 receiver with mgcamd emu.

My firmware:

S/W version 06020700_1.4.18 EMU
H/W/version ALI-HD-LV-VER3.0
Loader version M3602B 1.1.6

[suma]

Hi,
Confirmed, we'll check and fix ASAP

[cardsheranski]

No I haven't seen the pop-up. I assume that the changes will be active after 6.00 Moscow time? At this moment I'm logged in with the newcamd525 ports and the camd3 ports are not working yet.

[suma]

Does your receiver understand ignore and priority lists as Dreambox does?

[cardsheranski]

I don't know that?  I tried to load the list using usb but the tuner didn't recognized it.

What I just dit is put the subscription details (port number, username, password, emu selection and des key field.
When I was using newcamd525 protocol it was working. Now when I switched to camd3 I inserted the new ports and I got banned for two hours after connection attempt. It was after 6.00 am Moscow time.

[suma]

I don't know that?  I tried to load the list using usp but the tuner didn't recognized it.

What I just dit is put the subscription details (port number, username, password, emu selection and des key field.
When I was using newcamd525 protocol it was working. Now when I switched to camd3 I inserted the new ports and I got banned for two hours after connection attempt. It was after 6.00 am Moscow time.

http://www.cardsharing.cc/index.php?topic=28219.msg78745#msg78745

[cardsheranski]

Hi Suma,

I am aware of the fact that the problem is on my side and the ban is the way of telling me that.
What can I do to solve my isssue? My receiver is not very known on this forum or the internet. I allready tryid to load a different image but it was not a success. Shall I just go back to the newcamd525 protocol instead of camd3?

[suma]

Shall I just go back to the newcamd525 protocol instead of camd3?

Why don't you address to support forum of your receiver? I am sure, there must be the one.
Please explain what do you mean by glitching? Freezes, or stops of the picture, or what?
Sure, you can go back to newcamd protocol (please remember, that the times when you can change your protocol, are limited!).

regards

[cardsheranski]

With glitches is mean that the image stops every 10 or 20 seconds and then it goes further.
In the logfile I see a entry CW: failed. After few attempts I get banned for cascading.

Is it true that a mgcamd emu should be able to use both camd3 and newcamd525 protocols? Or is it just possible when using a linug based receiver? How can I check if my receiver is linux based?

[suma]

With glitches is mean that the image stops every 10 or 20 seconds and then it goes further.
In the logfile I see a entry CW: failed. After few attempts I get banned for cascading.

OK

Is it true that a mgcamd emu should be able to use both camd3 and newcamd525 protocols? Or is it just possible when using a linug based receiver? How can I check if my receiver is linux based?

No, it is not true. Mgcamd is used with newcamd protocol. Camd3 emulator is used with Camd3 protocol. These are different things.
Linux is an operating system (computer). The principle is that you can control your receiver via PC using specialised software. Can you manage settings of your receiver from computer? Or you are using only remote control?

[cardsheranski]

I am only using my remote control.

[suma]

Bugs of the firmware. Your receiver is not linux-based. Try to change firmware.