Кардшаринг НТВ+ на cardsharing .cc - самый надёжный и стабильный шаринг!
CardSharing Server ENG => Questions on cardsharing server => Тема начата: telex от 05 Июля 2015, 13:57:12
-
is the newcamd.list not working anymore with CWS at the beginning of the line?
Is it only 2 lines now?
Now I use mgcam with cccam protocol , before mgcam with newcamd.. ?
But newcamd was still working...?
-
can I still use newcamd? Any disadvantage?
when I use newcamd than I have to use the long line list?
-
There are only 2 protocols we use - newcamd and cccam.
Emulators used for this protocols are mgcamd, cccam and wicard.
In the billing, you are provided with CWS lines for mgcamd emulator (newcamd protocol), and you may use them for cccam emulator (description is available in the billing - Cccam protocol launched !!!).
For cccam via newcamd, you are provided with the only (1) line substituting all CWS lines (all ports in one).
-
in the billing (my subscription ) I see no CWS line anymore, only two C lines...
I think now I use mgcamd as emulator with cccam as protocol...?
-
can it be you write:
For cccam via newcamd
but you mean:
For cccam via mgcamd ?
-
Now I found newcamd to again :-)
but what is the better way? cccam via mgcamd or newcamd via mgcamd ?
-
Cccam is good for VIP packages (many CWS lines for eack package is replaced by the only line).
For MgCamd, you need to add each CWS line.
-
can it be you write:
For cccam via newcamd
but you mean:
For cccam via mgcamd ?
I asked you to open billing.
Cccam protocol launched !!!
Dear friends! We are glad to announce that cardsharing of all packages has been launched on our server using Cccam protocol!
Advantage of Cccam protocol, as compared to Newcamd protocol, is a possibility to enter all providers' CAIDs for one port. Simply speaking, all packages provided by CS are working with a single port. Currently, in order to connect to VIP package, it is sufficient to connect to the only port. Also, if one subscription is replaced with the other one, in the most cases, no changes in receiver settings will be required.
Cccam protocol can be also evaluated by the owners of non-linux receivers with a limited number of entries (servers). Now, it is not necessary to sacrifice any provider due to the limited number of entries in your receiver.
From now on, it is possible to share and watch NTV+Vostok package not only with linux-based receivers using Wicard emulator, but with all other receivers supporting Cccam protocol as well.
WARNING! It is allowed to connect to the server either using Cccam OR Newcamd protocol, as you wish, but NOT using the BOTH protocols at once!
In order to get settings for connecting with Cccam protocol, enter the billing, "My subscription" sub-menu, click to expand "Show settings for Cccam protocol" and below, you will see the settings generated for Cccam, Mgcamd, Oscam and Wicard emulators. All these emulators support Cccam protocol.
Please pay attention that either for Cccam and Newcamd protocol, settings are generated for both main and back-up servers (with protection against DDoS attacks). It is always required to get connected to the both servers at once - main and back-up, without selecting one of them. Only in this case, interruptions in CS will not be noticed if one of the servers will have any problems! Enjoy yourself!
-
but what has the better performance?
cccam via mgcamd or
newcamd via mgcamd
-
Equal, the difference is that for Mgcamd you need to add all entries for each port (CWS lines), and for Cccam you need the only entry with the only port.
-
спасибо ;-)