Channels won't open on mgcamd 1.35

[gunners4london]

Hello.
I have problem getting pictures on newcamd and mgcamd on my clarke-tech. I have downloaded the plugin and installed it. The folder is usr/keys on my box. I have put the files that I found on this forum there, and copied the CWS lines in newcamd.list. And when I turn to a channel the ecm/decryption type turns green, but no picture, and no information in hops and ecm time.
I have mostly tried out Cccam before, so I am pretty new to mgcamd. I have tested the N line on Cccam here but it freezes a lot, and oscam doesn't open all the channels but is more stable. Cccam does open all the channels, but freezes a lot. I would love to get mgcamd to work so do you have any solution

Best regards,

gunners4london

[suma]

Hi,
Probably, it depends on the firmware installed into your receiver. Maybe there is a conflict of versions (firmware and mgcamd). Try mgcamd 1.31 or 1.35. If you fail, try to flash your receiver with other firmware. No other solutions.

[gunners4london]

I have mgcamd 1.35 and pli firmware. Maby I could try to downgrade to 1.31, or change the firmware. Any firmware that you recommend?

Best regards,

gunners4london

[suma]

Complete your signature (i am not a magician to know what is your receiver, etc). To advice you, i need to know what is used.

regards

[gunners4london]

Sorry about that. Now I have put in the signature. I am new into the cardsharing and linux world, but Cccam is working with the n line, but not the mgcamd1.35.

Best regards,

gunners4london

[suma]

Sorry about that. Now I have put in the signature. I am new into the cardsharing and linux world, but Cccam is working with the n line, but not the mgcamd1.35.

Which config line is used with MgCamd?

[gunners4london]

I dowloaded the mgcamd 1.35 plugin from the menu of my clarke-tech. The only file that didn't appear in usr/keys was newcamd.list. This and all the other files I downloaded from this forum and copied it to usr/keys. Then I copied all the cws lines from my subscription site and pasted it. I get a green light on the information line I dowloaded from the plugin section, but no hops and ecm time and no picture.
Could I try to change to another image? Do you have any other soulution? Strangely it works with oscam and cccam. But why don't all channels open with oscam?

Best regards,

gunners4london

[gunners4london]

Now I have tried back and forward, and suddenly the pictures came trough. I googled and saw that other people had the same problem with clarke-tech. So I changed the box id to 06 in mg_cfg file and it worked.
But whu is it no hd channels on digital+ spain?
Thanks.

Best regards,

gunners4london

[suma]

Hi,
digital+spain is not guaranteed and has been removed from the billing.
No SD no HD channels

[biohazardx9]

This is interesting, I had an issue way back with the same, MGcamD not working. when I did a different firmware (one with MGcamD built in) it worked.....

When I fix my ethernet cable (I somehow snapped it in half  ), I'll re install edg nemesis and try the box id trick above.

For the info Clarktech / technomate seem to be clones of each other.


Big thumbs up for you Suma, doing a great job mate esp getting sky IT going again, can someone deliver a big crate of beer for him? 

[gokane1973]

Hi there.

I have Dreambox 800HD se with Open Pli image and have both CCcam installed and Mgcamd 1.35.

I have installed the config files from your website for Mgcamd, but the CWS line will not decode the SKY UK channels.  However when I put the Cccam "N" line into Cccam it DOES decode the channels ok, therefore I know the service is working 100%. 

I am not using the Cccam option at the moment as I know you recommend we all use Mgcamd for your server and I do not wish to be disconnected or banned!!

I have used Mgcamd previously with another provider so an unsure why I cannot get it to work this time.  I have changed all the settings and reinstalled Mgcamd but still doesnt work.  Is it possibly my image? 

Can I use Cccam all the time with no fear of being banned? Or is this not an option?

Thank you for your help

<Gareth>

[suma]

Is it possibly my image? 

Can be. Try other image.

Can I use Cccam all the time with no fear of being banned? Or is this not an option?

This is not an option. Cccam is prohibited. We use only mgcamd 1.35 or camd3 emulators. If you want to further experiment, you will do it at your own risk. Try any image supporting mgcamd 1.35.
Question: have you disabled Cccam when using Mgcamd? Any other emulators shall be disabled, only Mgcamd enabled.

regards

[gokane1973]

Hi Suma

Thanks for your quick reply.  Unfortunately I am unable to try another image as have my Dreambox set to use Open Pli always, tried all the other images and had problems with my Hard-drive.

As for the CCCam, yes I have noticed that this is always running even when I select Mgcamd.  I will try to delete CCcam, and only use Mgcamd, then use your settings. 

I will NOT use CCcam line if it is prohibited, and keep trying to get my Mgcamd line operating.  Thanks again for your advice and guidance!

<Gareth>

[gokane1973]

Hi there

I got it working, and I think the simple problem was that when rebooting the receiver / softcam, I was restarting Enigma 2 and it wasnt working.  Instead, when i rebooted the entire box from scratch, it worked perfectly!

Just info for anyone else who was having this problem.

Thanks Suma for your help and superb service.