Вход в биллинг - Billing entrance - www.CardsharingServer.com

English forum section

Автор Тема: Oscam Icam v3: Complete firmware for Zgemma H11S (ARM cpu)  (Прочитано 1417 раз)

TechGuy

  • -----
  • Администратор
  • Старожил
  • *****
  • Сообщений: 277
Oscam Icam v3: Complete firmware for Zgemma H11S (ARM cpu)
« : 27 Сентября 2022, 19:34:56 »
1. Introduction

We have prepared for you a ready-made OpenATV 7.0 firmware with Oscam-Icam installed and configured for Zgemma H11S (ARM cpu)

Attention! After using our backup, all data on your receiver will be deleted! Including your scanned channels, etc. Therefore, before installing, we strongly recommend that you make a full backup of your receiver!

After using our backup, you will need to make some settings – if necessary, change the configuration of your tuner, as well as specify your data for connecting to the CS server.

If you don’t have a Zgemma H11S receiver, please use other article!

2. Firmware installation for Zgemma H11S (ARM cpu)
  • Format your USB stick with a FAT32 file system
  • Download the USB image from HERE
  • Extract the USB image (it is a .zip archive) on your PC using your favorite unzip tool to the root directory of your USB stick. The result is that you get a directory images and force_h11.txt file.
  • Ensure no other USB devices are plugged into the receiver while flashing
  • Insert the USB stick containing the image files into one of the USB ports on the receiver, rear USB port is advised if possible.
  • When you enter the recovery menu then it will force to install the image from local USB stick. On OpenATV firmware you should go to Menu -> Setup -> Software Management -> Flash Online and choose Backup image openatv-7.0-zgemmah11s-backup-20220915_1322_usb.zip from the USB stick
  • After flashing receiver will be rebooted.
  • Remove the USB stick
  • Now you can start to configure the receiver. See instructions below (Go to step 3)

3. Setting up the receiver after flashing

3.1 Tuner Configuration

If, after flashing and turning on the receiver, the “kabel eins” channel did not work for you, then you need to change the tuner settings. To do this, go to the MENU -> Setup -> Reception -> Tuner Configuration section and configure your tuner.



3.2 Obtaining the IP address of the receiver

By default, the receiver should obtain a network address automatically (DHCP). To find out, you need to go to the section MENU -> Information -> Network



Connection status must be Up / Active, IP address must be defined (In my case it is 192.168.1.219)

If for some reason your receiver did not receive an address automatically, then you need to set up the network manually. This can be done in the section MENU -> Setup -> System -> Network -> Device Settings -> Adapter Settings



3.3 Setting up the Oscam

You need to add your access parameters to Oscam. To do this, open the Oscam Web Interface in a browser using the IP of your receiver. Oscam Web Interface is located on port 8080. In my case it is:

http://192.168.1.219:8080/

Login: admin
Password: icam2022

You need to go to the Files -> oscam.server section, specify your connection data taken from the billing and click the Save button.

ATTENTION! We found that sometimes when using oscam-icam the channels freeze for 7 seconds. We do not yet understand the nature of this error, we will check it. But it is known for sure that it only happens when you connect to the server using the cccam protocol. If you connect to the server using the Newcamd protocol, then this error does not occur. Therefore, if you have freezing images for 7 seconds – connect to the server using the Newcamd protocol!



Don’t forget to click the Save button!

4. Reboot the receiver

Please reboot the receiver completely after setup. Do not turn off the receiver from the socket, but reboot it through the menu MENU -> Standby / Restart -> Reboot

After rebooting the receiver, you can go to the Sky Deutschland iCAM bouquet and enjoy watching.




5. Additional Information

Installed firmware has a root password for remote access via SSH / Telnet:

Login: root
Password: icam2022

We recommend that you change the root password, and restrict or disable remote access if you do not need it.