Вход в биллинг - Billing entrance - www.CardsharingServer.com

English forum section

Автор Тема: CubeRevo 3000HDPVR (AB IPBox910)  (Прочитано 8331 раз)

uzas

  • Старожил
  • ****
  • Сообщений: 210
  • Cuberevo 3000 HD PVR
CubeRevo 3000HDPVR (AB IPBox910)
« : 11 Апреля 2009, 20:06:37 »
 ребята кто нибудь сталкивался как подключить шару нтв+ (софт NLB9207) последний эмуляторы стоят. newcamd  (пишут вносишь данные сервера  пароли  и все работает) и подправить mg_cfg
    http://satell.ucoz.ru/forum/10-42-1                     

 CWS_KEEPALIVE = 300
CWS = 127.0.0.1 32100 ip9000 nlbimage 11 12 13 14 15 16 17 18 19 10 11 12 13 14
CWS = 127.0.0.1 32101 ip9002 nlbimage 11 12 13 14 15 16 17 18 19 10 11 12 13 14
 

xtruex

  • Главный помощник Moderatora
  • Ветеран
  • ****
  • Сообщений: 5010
  • DM 500HD OpenPli 4
Re: CubeRevo 3000HDPVR (AB IPBox910)
« Ответ #1 : 11 Апреля 2009, 20:22:34 »
правильно ребята пишут
в биллинге эти строки есть, прописываешь в newcamd.list и смотришь
ICQ:290344
Бесплатный тест
http://www.cardsharingserver.com/index.php?module=test

uzas

  • Старожил
  • ****
  • Сообщений: 210
  • Cuberevo 3000 HD PVR
Re: CubeRevo 3000HDPVR (AB IPBox910)
« Ответ #2 : 11 Апреля 2009, 20:58:20 »
ребята забыл спросить а этот эмулятор( newcamd.list) подойдет на нтв+

xtruex

  • Главный помощник Moderatora
  • Ветеран
  • ****
  • Сообщений: 5010
  • DM 500HD OpenPli 4
Re: CubeRevo 3000HDPVR (AB IPBox910)
« Ответ #3 : 11 Апреля 2009, 21:04:10 »
ставьте Mgcamd_1.31
ICQ:290344
Бесплатный тест
http://www.cardsharingserver.com/index.php?module=test

uzas

  • Старожил
  • ****
  • Сообщений: 210
  • Cuberevo 3000 HD PVR
Re: CubeRevo 3000HDPVR (AB IPBox910)
« Ответ #4 : 11 Апреля 2009, 21:50:32 »
  вот что есть в этой прошивке 9207 есть там этот эмулятор


AbCom IPBox9 Series / CubeRevo nlb image
         Unofficial Custom release
     no limits board - http://www.nlb.to
       Image mod by Dexter
   ****************************************
   ****  Updated:  4 april 2009        ****
   ****************************************


Recent updates.
   NLB Panel 1.43
     - Added hypercam option in emu selection.
   NLB Panel 1.41
     - Install   pack.tar.gz from /tmp


Features of NLB Image
   - delay option in nlb panel for problems with newcs init card, such as nagra3 cards.
      - Germans should set delay to about 20-25 seconds, so it will decode at bootup
      - without need to restart cam.
   - NFS mount as replacement for internal HDD (for SD recording only)
       - HD/MPEG4 recording works too, but will studder as MPEG4 can be
        upto 20Mbyte/second and with 100Mbit network card, it will never work good.
   - Onscreen panel for stop/start of most features found in webif.
      - Internet update function for webif and panel for now.
   - Customized startup, faster load times
   - Added support for
      external usb serial port (PL2303 USB-Serial)
      Drivers are default loaded when you choose to use enable newcs.
   - Added binary utils
      - ssh / scp / sftp  (client tools)
      - fw_printenv / fw_setenv   (uboot environment see/change)
      - strace
      - cron daemon
   - Emus included (in /data folder, Read-Only)
     new updates should be placed in /var/bin .. (see name in []  )

      - [newcs]            newcs 1.62    (newest 23.10.2008)

      - [incubusCamd.sh4]  incubus 0.80   (newest 01.03.2009)
                 Now support dual tuner recording and pip.
                 Still unstable with certain types of cccam versions.

      - [mgcamd]           mgcamd 1.31

      - [mbox.sh40]        mboxII 0.4 Build 0023

      - [hypercam.ipbox]   hypercam v1.1


       - all key files should be put into /var/keys folder.

   - Samba (Windows networking sharing)
   - ftp / telnet / ssh server
   - terminfo for top (primarily)
   - USB multiboot (see below for details on how to use it)
      - supports all_noboot images too.. (except AbCom image)

   - WebIf (details below)

   - Bootscript for loading at every startup
      - /var/S59_bootscript  and remember "# chmod 755" on script


*********************
NFS Media setup howto
---------------------

DGS do now since 8728 support NFS, but to use it as /media, you need to ignore their mount.
it is handled in background.

the line in your /var/mount_manager_fstab should look similar to this.

nfs    /mnt/nfs        10.1.12.100      /var/nfsmediashare      dexter  dexter  NLBshare        Disconnected

IMPORTANT:  current release has one requirement "rule".. part of NFS sharelocation needs to include  nfsmediashare ,
so your share can be /media/nfsmediashare  or /movies/nfsmediashare or similar.... just remember to include that name in share.

after you configured this, you also need to enable in webif, and choose IP9000 -> Change NFS/HDD media.
you can edit the file and reboot box or you can configure in dgs application, but do not press "connect",
it will not work like this.

After you enabled it in webif, and configured the line in your mount manager, you can reboot and at next
boot you got /media mounted from your NFS server.

For those wondering why CIFS is not supported, its because CIFS do not support directio and also speed of CIFS
is worse than NFS.

Remember:  NFS starts with / infront of mountpoint.



*****
WebIf
-----
-----

The webif is your control center of the NLB mod image.
Default login is:  root    and  password: relook
If you need to update access table for ip addresses allowed to access webif, please
   edit the /var/etc/httpd.conf
   You find a line here ie.
    A: 192.168.
   Enter your network segment here, example
    A: 172.24.
   or a specific public ip
    A: 212.242.1.12
   Save file, and reboot box, and you got access to the webif.

- System information
   * Processes - List current applications running on IPBox
   * Change SWAP HDD - Activate Swap or disable it.
   * CPU Info - get IPBox cpu info details
   * System Boot information - output of "dmesg" startup of box.
      can be used even if your box shows "PANIC".

- System options

   * Format harddrive - Format your harddrive to be used with box.
              you cannot format if drive is in with timeshift.
              Use this option if your box disable your USB/external HDD during boot.
              unplug external usb hdd, and connect, and run this command.
   * Status change ushare - Start ushare with box when booting.
             Ushare is for sharing files on hdd to other UPnP/DLNA servers as Playstation3.
             note: default recorded files cannot be played, some if renamed with extension .mpeg
             this is primarily for those that put divx files onto hdd.     
   * restart ushare - reStart ushare if more files are added to folders.
   * restart samba - restart windows sharing service.
   * Samba status - Activate or stop samba/windows sharing services
   * Change HDD filesystem - Choose between ext2/ext3 or existing.
      ext2 filesystem will run FSCK (filesystem checks)
      ext3 filesystem skips FSCK
   * telnet status - Activate or stop telnet service
   * ssh status - Activate or stop ssh service
   * ftp status - Activate or stop ftp service
   * Restart box - Reboot your box

- Firmware options
   * Upgrade FW - Upgrade firmware from img file in /var or /media folder.
         transfer .img file to /var or /media folder and select this option
         to upgrade firmware.

   * Multiboot - Read below for details

- USB options

   * SWAP - activate or disable swap on USB key

   * Format USB linux   - format a usb pendrive/stick for use with box
                   - and for multiboot setup

   * Format USB windows - format a usb pendrive/stick for use with box as FAT/FAT32
            Multiboot will not work with this formatting

   * Mount USB - mount a USB stick on box, to access files on it
      location:  /mnt/usb/usb0
   * Copy /var - make backup of /var to your usb stick
   * backup db.dat to usb - copy your db.dat file to your usb stick
   * restore db.dat from usb - restore db.dat (will be named db.dat.edited)
      requires reboot to take effect.
   * List contents of usb - list contents of usb stick, if mounted.

- IPBox options
   * Change powerled - Change state of powerled when in use.

   * Change card driver - Change type of card driver
      - choose between original DGStation driver.
      - and customer driver (checked with german cards) which is default.

   * HDD/NFS media folder change - Choose to use NFS share as /media folder.
   * Change Fan - enable/disable fan in Ipbox.
   * Show time in led -  activate Time in VFD display.
   * Change led - Change VFD brightness (0-7)
   * stop sbox at next boot - will disable start of "satbox" application at next boot (debug)
   * Assign color button - Read/Yellow/Green buttons can be assigned functions
      most options above + more described below here.
         favpip     - get favpip to open with shortcut key.
         WideScreen - stretch tv picture on TV's that do not do it automatically.
         ecm info - show current ecm info on tv
         hdd temp - Show HDD temperature on tv display
         restart cam - says what it does
         stop cam -  -- !! --
         Soft updater - run your /var/bin/soft script

   * Change skin - Change the look of your menus in DGStation satbox application.
         * Skin:  Crash Blue
         * Skin:  Crash Grey
         * Skin:  Crash DeepBlue
   * display HDD temp - show current temperature of HDD
- Emu
   * AutoStart emu - Start emu at boot.
   * Change emu - Select between  mgcamd / mbox , to be
         automatically startup at boot.
   * Stop Emu - Stop running emu.
   * Restart Emu - Restart running emu.
   * Change newcs status - choose to stop or start newcs at bootup.

   * Change newcs config - Choose between both/upper/lower newcs default config
             - this will overwrite your existing configuration.
             - added more configs for nordic and german cards.
   * ECM - Show current ECM of provider.
   * Mgcamd shares - show current connections
   * Card stats - mgcamd status
   * Info about cards - if gbox peer enabled, shows current list of cards.

- Keys update
   * Sxxxx.Kxx Update
      runs your /var/bin/soft script


**************************
EMU DEFAULT CONFIGURATIONS
--------------------------
--------------------------
hypercam
   included is a default config.

mgcamd
   included is a default config to run with newcs and
    use internal card readers (activated default)
   originally tested with Viasat and CanalDigital cards.
mbox
   included is a default config to run with newcs and
    use internal card readers (activated default)
   Tested with CanalDigital card.
   Now includes 32100.list, 32101.list with default all channel opened.
incubusCamd
   is included, defaults are still for use with newcs and this is a beta release of cam.


*************
USB MULTIBOOT
-------------
-------------
- Multiboot feature gives you the option to boot off a usb pendrive/stick, so you can
   more easily place as many files you wish into the root file system, with the only
   limit of the usb filesystem size.
- It also uses the USB pen for /var storage, so each image will have its own setup.
- Removing the usb pen, will cause box to boot flash image.
- USB pen should be formatted in webif, before use
- other USB pen cannot be used/formatted in webif, when you are running multiboot.

Instructions for usb multiboot
------------------------------
   - Format a usb pen in webif  (USB Options - Format USB)
     (old formatted usb sticks from 8022 and down needs reformatting)

      if used with box during mp3 playback or photo album, remember to mount before
      you goto player.

   - Wait for an OK from formatting (takes 30-60 seconds depending on size)
   - Placing firmware on usb pen procedure
      - * For /media folder
        - with ftp copy an .img file to the /media folder
        - Only DGS / SifTeam / NLB images will work.
      - * For /mnt/usb/usb0 folder
        - mount usb pen in webif (USB options - Mount USB)
   - select Firmware Options - Multiboot
      - in field "Enter name ...." write a suitable name for image
      - in "Choose file to put on usb" select image to put on usb
        - in front of img file you can see location of file.
      - Press "extract" to extract image to usb.
      NOTE: IF NO USB PEN IS INSERTED YOU DO NOT HAVE OPTION TO INSTALL IMAGES!
            OR FORMATTED CORRECTLY, ie. Windows formatted pen will NOT work.
   - when finished (takes 2-3 minutes), reselect "Firmware Options - Multiboot"
      - In bottom "Select USB bootimage to use" you can now see your image.
        ? if it is not shown and extract failed, make sure your usb was
          formatted with a unix fs, ie. using format usb in webif.
   - You can choose to "Change" and mark which image to load at next boot
     or
   - You can choose to "Delete" firmwareimage from usb.
   - Selecting "Flash boot" will make box boot your flash / disable usb boot.
   - Reboot box to start usb firmware.
 
   







xtruex

  • Главный помощник Moderatora
  • Ветеран
  • ****
  • Сообщений: 5010
  • DM 500HD OpenPli 4
Re: CubeRevo 3000HDPVR (AB IPBox910)
« Ответ #5 : 12 Апреля 2009, 08:28:53 »
если уже стоит Mcamd_1.31 прописывайте строки из биллинга как написано в описание и наслаждайтесь просмотром
ICQ:290344
Бесплатный тест
http://www.cardsharingserver.com/index.php?module=test