Кардшаринг НТВ+ на cardsharing .cc - самый надёжный и стабильный шаринг!
CardSharing Server ENG => Hardware => Amiko => Тема начата: gge0rge802 от 05 Марта 2013, 02:31:52
-
Hello
I just bought a new amiko mini HD. I am totaly new to cardsharing. Can I buy a subscription from you and use it with this receiver? Can you help me set it up? Thanks a lot!
-
Hi,
1. Read FAQ http://www.cardsharing.cc/index.php?board=30.0
2. Read everything about plugins and emulators http://www.cardsharing.cc/index.php?board=60.0
3. Read about configs http://www.cardsharing.cc/index.php?board=99.0, and
4. sub-topics Re: Amiko receiver settings http://www.cardsharing.cc/index.php?board=155.0
Take a free test in the billing (you may take a free test as many times as you like until you adjust your receiver for sharing. If you are satisfied with the quality, you may take paid subscription.
regards
-
Hello
I did read all this, but I cannot connect to server. I purchased a subscription for 3 days in order to check if I can get it working.
I flashed the proper firmware but I cannot configure the settings in order to connect to the servers.
From the amiko mini menu I can edit info for 7 servers
On the first server I edit the following info:
SERVER NAME: I add the name of server according to my subscription
SERVICE PORT: I add one of the ports you provided
USERNAME: I add my username account
CODE: I add my password
DES KEY:here it writes 01 02 03 04 05 06 07 08 09 10 11 12 13 14. I left it as is. I can only change the numbers with letters c/d/e/f
EMULATOR: I can choose between these: newcamd, homecamd, homecamd2, cccamd, nasscamd, deltacamd, spidercamd, spidercamc, avatarcamd, xcamd, mgcamd, ishare, skycamd, gscamd, KZcamd, anacondacamd. I chose newcamd but nothing happened.
Then I added a second server with the same info as above but as SERVICE PORT I added the second port you provided with my subcription.
THe orther server are blank and inactive
Finally I can choose for server between: Nass active, delta active, spider active, avatar active, xcamd active, tm active, gscamd active, skycamd active, kz active, anacond aactive. I left it Nass active which is the default.
Please help if you can
-
Have you read the complete thing on Amiko http://www.cardsharing.cc/index.php?board=155.0 ?
-
Yes I did. I did not find anything useful
-
So, my advice - find any support forum of your receiver and ask there
http://www.sat-support.tv/forum/
-
I just managed to get it working!
I will post the complete process this afternoon.
-
I just managed to get it working!
I will post the complete process this afternoon.
could you post your solution? I have wanted to use miniHD but it was not working well - lots of freezes.
-
hello if you solve your issue of configuratione of amiko mini hd can you help me?i have same issue and i dont know how to move :'(me than
-
Hi m8, Did you get it all working in the end? I've just brought a amiko mini hd combo & was thinking of setting it up on a motorised setup with a line. Any info would be a big help.
Thanks
-
This is how you set it up :) for the Amiko mini combo hd.
1. Press menu + internet + net client config.
2. Select sever & press yellow to edit. Enter your details ie.
3. SERVER NAME: I add the name of server according to my subscription
SERVICE PORT: I add one of the ports you provided
USERNAME: I add my username account
CODE: I add my password
DES KEY: 01 02 03 04 05 06 07 08 09 10 11 12 13 14
Active sever Ok
Emm Enable Ok
Emulator Newcamd
4. Click activate + store + exit
5. Enjoy 8)