Кардшаринг НТВ+ на cardsharing .cc - самый надёжный и стабильный шаринг!
CardSharing Server ENG => Configs => Тема начата: giees от 01 Сентября 2015, 21:05:57
-
Subscription start yesterday. Yesterday worked fine, but from today I have some problems. I have many freezing, and in my account in "Connections history" this message: "Requests to the main and reserve server for decoding of different channels were detected at the same time. It is strictly prohibited by the rules! It is allowed to connect the only receiver and the only emulator to the server and watch the only channel. Violation of rule No.12"
But I have ONE receiver, ONE emulator and watch the ONLY channel. What's wrong?
-
Maybe, Cccam emulator is the reason? Are you sure, it is set up properly?
Try Mgcamd 1.35
https://www.cardsharing.cc/index.php?topic=31986.0
Also refer to the Hardware sub-forum https://www.cardsharing.cc/index.php?board=56.0 re: Opticum receivers. Maybe you will find some helpful information...
-
My subscription start month ago and everything worked ok. The problem started a few days ago.
Important!
Serious rules violations detected! Your account may be disabled!
Please study the history below and read recommendations how to eliminate problems.
EMM requests 1300
IMPORTANT! Your receiver is sending EMM requests to the server. It is not allowed by the rules....
Total of connections per day 1300
IMPORTANT! A large number of reconnections to the server detected. Violation of rule No.2
Please note. The same number of EMM requests and connections.
Requests received 8578
Requests decoded 7208
Requests rejected 1370
- Channel not decoded 78
- Requests filtered 1290
I need some help in problem solving. What am I doing wrong? And how can I begin to try to fix the problem?
oscam.conf
#oscam.conf
[dvbapi]
enabled = 1
boxtype = dreambox
user = dvbapiau
au = 0
request_mode = 1
[webif]
httpport = 16002
httpuser = x
httppwd = x
httprefresh = 20
httpallowed = 127.0.0.1,192.168.0.1-192.168.255.255,10.0.0.1-10.255.255.255
----------------
oscam.user
[reader]
label = "mXXXXXXXXXXX.XXX_XXXXX"
protocol = cccam
device = sXXXXX.XXX,XXXXX
user = XXXXX
password = XXXXXX
group = 1
audisabled = 1
[reader]
label = "bXXXXXXXXXXX.XXX_XXXXX"
protocol = cccam
device = sXXXXXXX.XXX,XXXX
user = XXXXX
password = XXXXXXX
group = 1
audisabled = 1
fallback = 1
--------------
#oscam.server
[reader]
label = lower
protocol = internal
device = /dev/sci0
detect = cd
mhz = 500
cardmhz = 500
group = 1
emmcache = 1,3,15
deprecated = 1
[reader]
label = upper
protocol = internal
device = /dev/sci1
detect = cd
mhz = 500
cardmhz = 500
group = 2
emmcache = 1,3,15
deprecated = 1
[reader]
label = "mXXXXXXXXXXX.XXX_XXXX"
protocol = cccam
device = XXXXX.XXX,XXXXXX
user = XXXXXXX
password = XXXXX
group = 1
audisabled = 1
[reader]
-------------
oscam.dvbapi
P: 0B00 1
P: 0B02 1
-------------
label = "bXXXXXXXXXX.XXX_XXXXXX"
protocol = cccam
device = XXXXX.XXX,XXXXXX
user = XXXXXX
password = XXXXXX
group = 1
audisabled = 1
fallback = 1
--------
-
What is your receiver ?
What is your login ?
Why use oscam if does not know how to configure....
-
What is your receiver ?
What is your login ?
Why use oscam if does not know how to configure....
Image: OpenVIX 3.2.010
Golden Interstar Xpeed LX1 1 x DVB-S2
Image come with step-by-step guide and it was pre-configured image. That is why oscam.
I can sent login names with private message if needed.
Now everthing works ok. I reinstalled the image and use only one active subscription.