Вход в биллинг - Billing entrance - www.CardsharingServer.com

English forum section

Автор Тема: Vu+ Solo2 + VIX, MgCamd 1.35 + Sky HD UK, recording problems  (Прочитано 15443 раз)

rost2527

  • Новичок
  • *
  • Сообщений: 7
This is my first post and i am pulling my hair out, i have been trying to setup my VU+ SOLO2 box with VIX and MgCamd 1.35 with SKY UK HD.

I can view all channels with no problems but once i start recording two HD pay per view NOT the freeview (freeview channels are all ok) channels after about 3-5mins the picture freezes, if i leave it after about a minute the picture comes back for about another 3-5mins then freezes again and so on, when if freezes if i restart the softcam the pictures comes back immediately.

I have setup the mg_cfg as default from here below:

# EMM messages
#    00 don't show any EMMs (default)
#    01 show only valid EMMs
#    02 show valid and bad EMMs with complete data display
M: { 00 }

# ECM messages
#    00 don't show anything about ecm
#    01 normal mode, show pids processed, decoded ecm and cw
#    02 verbose mode, show valid and bad ECMs with data
C: { 01 }

# AU
#    00 disable, no emm pids processed
#    01 enable, emm pids always processed for soft-au and shared cards
#    02 auto, emm started only if channel cant be decoded
#    03 process emm pids for network cards update only
A: { 00 }

# key update (sum 01 or 02 with 04)
#    01 update only new keys, default setting
#    02 update all keys (used for valid PMK checking)
#    04 enable TPS au
#    + tps SID, which pmt pid contains au pid
U: { 02 } 0x12c0

# config files folder (softcam, autoroll, ignore/priority)
#    00 files in /var/keys
#    01 files in /tmp
T: { 00 }

# network mode, use summ for several clients
#    00 no network (default)
#    01 newcamd netclient
#    02 radegast netclient
#    04 camd3 netclient
#    08 gbox netclient
#    32   cccamd netclient, card list saved as /tmp/cccamd.info
#       (ECM only, supported server version up to 2.1.1, later not work)
G: { 01 }

# network retry, use summ for several options
#    00 disable
#    01 retry every new ecm
#    02 try to connect to offline shares every Q: seconds
#    04 try to detect and fast reconnect to lost (and not used atm) server
#    + XX messages number and YY seconds to reconnect
#    mg will reconnect to server, if no answer to last XX ecm/keepalive or
#    if no answer for last ecm or keepalive sent for YY seconds
#    set to 0 to disable
N: { 07 } 360 3600

# network ecm timeout in seconds
K: { 07 }

# newcamd dead routes connect retry, sec
Q: { 60 }

# network shares priority
# 00 gbox, newcamd, cccamd, radegast, camd3 (default)
# 01 camd3, radegast, cccamd, gbox, newcamd
# 02 cccamd, newcamd, camd3, gbox, radegast
P: { 00 }

# on screen display type
#    00 No OSD (default)
#    01 neutrino
#    02 enigma
#    03 relook
#    + user password for http auth
O: { 02 } root password

# on screen display Options, summ of:
#    01 show emu ecm
#    02 show network shares messages
#    04 show decoding failed / fta
#    08 show emm keys update
#    + web port to use for osd
S: { 03 } 80

# Log option, summ of:
#    00 off
#    01 network udp log
#    02 log to console
#    04 file, appended ! delete it by yourself, before it eat all your hdd
#    + IP udp-port log-file-name
L: { 00 } 172.16.1.1 28007 /tmp/mgcamd.log

# keep ecm cache, seconds
# every cache entry takes 28 bytes, so 24h cache will take *only* 240-400kb of memory,
# for openbox/elanvision users with remote shares make sense to set it higher than default value,
# to not hammer cards while timeshifting or playing crypted recordings.
E: { 00 }

# cache option, summ of:
#    00 Off (default)
#    01 Ecm pids cache, store pids used to decode in /tmp/ca_cache.list at exit, load at startup, same syntax as restore.list
#    02 Ecm data cache, remember CW for (E:) time
#    04 Emm cache for network cards, do not resend the same emm twice, cache not cleared until restart
H: { 00 }

# reread files, summ of:
#    00 No (default)
#    01 reread config file on channel change (including priority and ignore, but not replace/cache)
#    02 reread SoftCam.Key on channel change
#    04 reread SoftCam.Key if file changed
R: { 00 }

# debug, summ of
# 00 off (default)
# 01 debug ecm
# 02 debug emm
# 04 debug network ecm
# 08 debug network emm
# 16 debug network login
# 32 show mem/cpu stats every 1 min
# 64 add timestamp to log messages
D: { 31 }

# box type
# 00 autodetect, change only if you think wrong type detected.
# 01 dbox2
# 02 dreambox
# 03 triple-dragon
# 04 relook
# 05 openbox
# 06 dreambox/mips
# 08 stapi/kathrein
# 09 stapi/ipbox
# 11 stapi/openbox
B: { 06 }

# map all 180x nagra caids to 1801
# default is 01
F: { 00 }


and the newcamd.list as follows:

CWS_KEEPALIVE = 300
CWS_INCOMING_PORT = 21000
CWS = server*.cc ***** username password 01 02 03 04 05 06 07 08 09 10 11 12 13 14 wan cardserv (AS COPIED FROM MY DETAILS)


Does anyone have any ideas, i have also tried the box at different address to rule out internet problems, i have tried VTI, BH images all the sames problems i sure its a config problem but i am new to this and now need help.

Thanks in advance.
VU+ Solo2, MgCamd 1.35, Sky UK HD + ViewAsia + ZeeTV 28E

suma

  • Модератор
  • Ветеран
  • *****
  • Сообщений: 10091
  • Keep trying!
Re: Vu+ Solo2 + VIX, MgCamd 1.35 + Sky HD UK, recording problems
« Ответ #1 : 17 Июня 2013, 05:59:58 »
Hi,
Have you read posts re: VU+ receivers here http://www.cardsharing.cc/index.php?board=53.0 ?
VU+Zero. 13E, 82.5E, 56E, Vip All, OpenPLI 6.0 image, OSCam: 1.20-unstable_svn. ALL POSTS WITHOUT SIGNATURE AND LOG-FILE will be ignored and deleted!1.mg_cfg here http://www.cardsharing.cc/index.php?topic=23717.msg58140#msg58140
2. ignore-priority.lists here http://www.cardsharing.cc/index.php?topic

rost2527

  • Новичок
  • *
  • Сообщений: 7
Re: Vu+ Solo2 + VIX, MgCamd 1.35 + Sky HD UK, recording problems
« Ответ #2 : 17 Июня 2013, 15:33:44 »
Yes i have looked at nearly all the posts on here and have used your signature links with no success.

Back to the drawing board, i was hoping that someone else on here has a VU+ Solo2 box and maybe try there mg_cfg file.

Thanks again.
VU+ Solo2, MgCamd 1.35, Sky UK HD + ViewAsia + ZeeTV 28E

rost2527

  • Новичок
  • *
  • Сообщений: 7
Re: Vu+ Solo2 + VIX, MgCamd 1.35 + Sky HD UK, recording problems freezing.
« Ответ #3 : 08 Июля 2013, 22:33:09 »
Still having recording problems, I can watch premium channels ok with no freezing, i can also watch a premium channel and record the same channel with no freezing, the problem i have is if i record one premium channel and watch a different premium channel then after about 3-5mins the picture freezing and comes back on.

I have just purchased a Gigablue 800HD Quad box to test and have had all the same problems with my VU+ Solo2 box with the picture freezing. I am using Mgcamd 1.35a with the lastest VIX image and the default setting above, i have tried BH, openPLI images and different cams.

I am contacting my broadband provider to check the line but i have 68mb DL and 18mb UL so this should be OK, and it seems to be stable connection.

Really running out of ideas and really need help to solve this, i have tried may different mg_cfg files etc with no fix

Will try and get the log files uploaded.

HELP PLEASE.

Thanks
VU+ Solo2, MgCamd 1.35, Sky UK HD + ViewAsia + ZeeTV 28E

suma

  • Модератор
  • Ветеран
  • *****
  • Сообщений: 10091
  • Keep trying!
Re: Vu+ Solo2 + VIX, MgCamd 1.35 + Sky HD UK, recording problems
« Ответ #4 : 09 Июля 2013, 05:10:35 »
Do you have dual-login active?
VU+Zero. 13E, 82.5E, 56E, Vip All, OpenPLI 6.0 image, OSCam: 1.20-unstable_svn. ALL POSTS WITHOUT SIGNATURE AND LOG-FILE will be ignored and deleted!1.mg_cfg here http://www.cardsharing.cc/index.php?topic=23717.msg58140#msg58140
2. ignore-priority.lists here http://www.cardsharing.cc/index.php?topic

rost2527

  • Новичок
  • *
  • Сообщений: 7
Re: Vu+ Solo2 + VIX, MgCamd 1.35 + Sky HD UK, recording problems
« Ответ #5 : 09 Июля 2013, 12:51:34 »
No only have a single login, is this were i'm going wrong?  So i guess i'm not able to record one channel and watch a second at the same time.

Thanks for your quick response SUMA.

VU+ Solo2, MgCamd 1.35, Sky UK HD + ViewAsia + ZeeTV 28E

suma

  • Модератор
  • Ветеран
  • *****
  • Сообщений: 10091
  • Keep trying!
Re: Vu+ Solo2 + VIX, MgCamd 1.35 + Sky HD UK, recording problems
« Ответ #6 : 09 Июля 2013, 12:57:02 »
With a single login, you are able to watch and record the channels from the same transponder only.
With a dual-login (1.5 times more expensive), you will be able to watch and record any channels.
VU+Zero. 13E, 82.5E, 56E, Vip All, OpenPLI 6.0 image, OSCam: 1.20-unstable_svn. ALL POSTS WITHOUT SIGNATURE AND LOG-FILE will be ignored and deleted!1.mg_cfg here http://www.cardsharing.cc/index.php?topic=23717.msg58140#msg58140
2. ignore-priority.lists here http://www.cardsharing.cc/index.php?topic

rost2527

  • Новичок
  • *
  • Сообщений: 7
Re: Vu+ Solo2 + VIX, MgCamd 1.35 + Sky HD UK, recording problems
« Ответ #7 : 09 Июля 2013, 13:02:49 »
Hi SUMA,

I have just been reading the posts with reference to the dual-login, i now see were i am going wrong.  As my box has a dual tuner could i buy another year package of SKY HD UK and use two separate logins on the one box to allow me to dual record etc using tuner A and tuner B?

Thanks again.
VU+ Solo2, MgCamd 1.35, Sky UK HD + ViewAsia + ZeeTV 28E

rost2527

  • Новичок
  • *
  • Сообщений: 7
Re: Vu+ Solo2 + VIX, MgCamd 1.35 + Sky HD UK, recording problems
« Ответ #8 : 09 Июля 2013, 13:04:33 »
Hi SUMA,

SKY HD UK doesn't support DUAL-LOGIN is there another way around this??

VU+ Solo2, MgCamd 1.35, Sky UK HD + ViewAsia + ZeeTV 28E

rost2527

  • Новичок
  • *
  • Сообщений: 7
Re: Vu+ Solo2 + VIX, MgCamd 1.35 + Sky HD UK, recording problems
« Ответ #9 : 09 Июля 2013, 13:41:59 »
I have now found the answers i was looking for dual accounts on the same box is a no, no.

Thanks for all you help.
VU+ Solo2, MgCamd 1.35, Sky UK HD + ViewAsia + ZeeTV 28E

suma

  • Модератор
  • Ветеран
  • *****
  • Сообщений: 10091
  • Keep trying!
Re: Vu+ Solo2 + VIX, MgCamd 1.35 + Sky HD UK, recording problems
« Ответ #10 : 09 Июля 2013, 14:47:06 »
Hi SUMA,

I have just been reading the posts with reference to the dual-login, i now see were i am going wrong.  As my box has a dual tuner could i buy another year package of SKY HD UK and use two separate logins on the one box to allow me to dual record etc using tuner A and tuner B?

Thanks again.

It is not possible to have 2 different logins using 1 receiver with 2 tuners onboard. You need 2 logins and 2 receivers.
As for dual-login, it is available not for all packages. Please refer to the billing, you will find info re: dual-logins in the subscription columns.
VU+Zero. 13E, 82.5E, 56E, Vip All, OpenPLI 6.0 image, OSCam: 1.20-unstable_svn. ALL POSTS WITHOUT SIGNATURE AND LOG-FILE will be ignored and deleted!1.mg_cfg here http://www.cardsharing.cc/index.php?topic=23717.msg58140#msg58140
2. ignore-priority.lists here http://www.cardsharing.cc/index.php?topic