Вход в биллинг - Billing entrance - www.CardsharingServer.com

English forum section

Автор Тема: Humax 5400 with WINCSC  (Прочитано 4964 раз)

arisarts

  • Пользователь
  • **
  • Сообщений: 10
Humax 5400 with WINCSC
« : 31 Октября 2011, 17:13:52 »
Hi.
I need some help.

I Have a dreambox DM500 and its working great with my subscription (newcam5.35).

I want to use my good old humax 5400 instead of Dreambox (and then buy another subscription for 2nd TV)

I have found many programs like maxshare or wincsc and I have managed to add my account but when I change the channel to it on humax it does not calling the software.

What do I miss?

Any help regarding Humax 5400 will really appreciated.

Regards

Aris
DM500s Gemini 4.70 GSF Image,
VU+Solo Black Hole 1.7.8
 Mgcam135a,(newcamd)

suma

  • Главный помощник Moderatora
  • Ветеран
  • ****
  • Сообщений: 10091
  • Keep trying!
Re: Humax 5400 with WINCSC
« Ответ #1 : 02 Ноября 2011, 08:51:10 »
Hi,
this is from old materials dated July 10, 2006. Not sure that this is still actual.
Reference http://www.cardsharing.cc/index.php?topic=36.msg59#msg59:

If you want to connect sharing server, you will need the following:

1) Upgrade your receiver with ToH3.4_HoT7.5.hdf firmware (see http://www.cardsharing.cc/index.php?topic=36.msg59#msg59 attached files)
2) Load PMC table - PMCT_hoT 7.5 (the table is valid, however not all providers have been compared)
3) Enter Humax menu  ToH ->Config -> and set a) CAID Preselect CARD+S+EMU , b) Sharing Protocol Mode SSSP
4) Connect Humax5400 to the PC using null-modem cable (if disconnected), with the PC and receiver being disconnected from power!
5) Run mpcs 0.8 or later.
Open mpcs.server file using Notepad and edit newcamd protocol (the first 11 entries). The next entries are related to camd3 protocol (because it is UDP protocol, we will not discuss it). So, from the first 11 entries, we need to change only entry 4 and entry 6.  4) Device         = dw.dyndns.org,10001 (here, add server name and port No. generated in the billing) 6) Account        = name,passw (here, add your login and password respectively) DES key remains unchanged. If you watch several packages using several ports, you need to copy the first 11 entries and paste them below changing only port No. corresponding to appropriate package. Better to change protocol (from newcamd to camd3, all packages are using the only 1 port). Save file. If your receiver is not connected via COM1 , but other port, open mpcs.conf file and in Device = tuner@/dev/ttyS0?delay=1&timeout=300. change port.  Here, COM port is specified in linux format ( example: ttyS0=COM1, ttyS1=COM2, ttyS2=COM3 etc.)  Save file, run mpcs.exe, DOS window will pop up, and you must see a picture on your Humax. It happens if you entered right entries.
6) Enjoy.

P.S. There are Sharmax and HSIC sharing software which can also be run. My reply is- this is a headache....
VU+Zero. 13E, 82.5E, 56E, Vip All, OpenPLI 6.0 image, OSCam: 1.20-unstable_svn. ALL POSTS WITHOUT SIGNATURE AND LOG-FILE will be ignored and deleted!1.mg_cfg here http://www.cardsharing.cc/index.php?topic=23717.msg58140#msg58140
2. ignore-priority.lists here http://www.cardsharing.cc/index.php?topic

arisarts

  • Пользователь
  • **
  • Сообщений: 10
Re: Humax 5400 with WINCSC
« Ответ #2 : 02 Ноября 2011, 23:59:23 »
Dear Suma

Thank you VERY MUCH for your time and efforts.

I will give it a try and let you know about the results.

BR

Aris

Hi,
this is from old materials dated July 10, 2006. Not sure that this is still actual.
Reference http://www.cardsharing.cc/index.php?topic=36.msg59#msg59:

If you want to connect sharing server, you will need the following:

1) Upgrade your receiver with ToH3.4_HoT7.5.hdf firmware (see http://www.cardsharing.cc/index.php?topic=36.msg59#msg59 attached files)
2) Load PMC table - PMCT_hoT 7.5 (the table is valid, however not all providers have been compared)
3) Enter Humax menu  ToH ->Config -> and set a) CAID Preselect CARD+S+EMU , b) Sharing Protocol Mode SSSP
4) Connect Humax5400 to the PC using null-modem cable (if disconnected), with the PC and receiver being disconnected from power!
5) Run mpcs 0.8 or later.
Open mpcs.server file using Notepad and edit newcamd protocol (the first 11 entries). The next entries are related to camd3 protocol (because it is UDP protocol, we will not discuss it). So, from the first 11 entries, we need to change only entry 4 and entry 6.  4) Device         = dw.dyndns.org,10001 (here, add server name and port No. generated in the billing) 6) Account        = name,passw (here, add your login and password respectively) DES key remains unchanged. If you watch several packages using several ports, you need to copy the first 11 entries and paste them below changing only port No. corresponding to appropriate package. Better to change protocol (from newcamd to camd3, all packages are using the only 1 port). Save file. If your receiver is not connected via COM1 , but other port, open mpcs.conf file and in Device = tuner@/dev/ttyS0?delay=1&timeout=300. change port.  Here, COM port is specified in linux format ( example: ttyS0=COM1, ttyS1=COM2, ttyS2=COM3 etc.)  Save file, run mpcs.exe, DOS window will pop up, and you must see a picture on your Humax. It happens if you entered right entries.
6) Enjoy.

P.S. There are Sharmax and HSIC sharing software which can also be run. My reply is- this is a headache....
DM500s Gemini 4.70 GSF Image,
VU+Solo Black Hole 1.7.8
 Mgcam135a,(newcamd)