Starview HD Combo +

[sz00gun]

Hello, I have a Starview HD Combo ( example: http://www.techkings.org/starview/6783-starview-hd-combo-firmware-flashing-guide.html  or  http://www.youtube.com/watch?v=MMQ-wX3lGDs )

There is a CCCAM and NEWCAMD and I used to use C lines for sharing, and everything worked properly. Do this service provide C lines as well? I have a 3 days test but I cannot see C lines, only: N lines, newcamd525, CWS, cs357x on my subsciption

Regards

[suma]

Hello,
This service provides N lines, you can see them in the billing after you arrange your subscription. However, CCCam is not recommended for use with our server. The most recommended emulators are Mgcamd 1.35 (for Newcamd protocol) and Camd3.
If CCCam is used, you will be using it at your own risk. We do not accept any claims if users are using CCCam.

regards

[sz00gun]

Thanks for replay. I'm going to buy Dreambox 800HD se later on. Perhaps in 3-4 months.... Till this time I have to use this bloody Starview ;(

I take that risk and I try using CCCAM, bit I cannot either connect to the server, nor to NEWCAMD, any ideas why? There where should be C lines I typed N lines... and nothing been happend ;(  no connected...

[suma]

To use Newcamd protocol and MgCamd 1.35 emulator, you need no C line. CWS line(s) is required. They are added to newcamd.list file. That's all.
I do not know structure of your receiver, so, you have to consult support forums of your model how to Re: mgcamd and newcamd.

regards

[sz00gun]

Ohhh I see... I affraid I have no access to any files on my box. This what I can do is choose CCCAM or NEWCAMD and type: host, username, passwort and port, only. That's it.

[suma]

Name or IP address - try to use our IP address (ping...)
Moreover, if it supports newcamd, it shall be set up automatically without CWS lines: only IP address, port No., user name, password.
I am not sure, this will help.

[suma]

By the way, I don't see any Ethernet ports from the rear of your receiver. If so, you have to use MPCS on your PC via RS-232 on your receiver. http://www.cardsharing.cc/index.php?topic=1362.0
This is a sh.... Hope, you understood what i mean.

[sz00gun]

You are very perceptive That version is without LAN, but my receiver have a LAN version, I attached a real photo

[suma]

From billing info, you have Vip HB subscription with Camd3 protocol. You need to urgently change it to Newcamd protocol TODAY.
Tomorrow morning (after 6:00 AM Moscow time) add CWS line data to your settings using Newcamd protocol. On the 1st picture, you have a screen of CCCam, change it to Newcamd and add data from the billing TOMORROW morning, because option of protocol change will be active next morning only.
As I explained you before, add server name, Port No, you login and password received from the billing.
Tomorrow I will wait for your results.

P.S. I don't know - how many entries can you add to your newcamd settings. If your receiver supports multiple entries, add the CWS lines one by one.

regards

[sz00gun]

ok. I'll try do this tomorrow. But I don't know what's are those data in lines: wan cardserv. I have no space in my receiver for this. Is it mandatory?

[suma]

You need to use newcamd page of your emulator and data required: (server) name, port No., ID (login) and password

Example:
(no wan) abcdefghij1.aa (no cardserv)
55555
sz00gun
password
DES KEY: 0102030405060708091011121314

That's all
Don't forget: after you changed protocol (in the billing), your subscription will be activated next morning after 6:00 AM (Moscow time)

[sz00gun]

Works properly. No freezing. I'm impress. Thanks